|
|
Clinch Knot This is probably the most popular fishing knot used today. When tied properly it is very strong and doesn't slip. It is perfect for lures. 1. Pass the line through the eye of the hook, or swivel. 2. Double back. make five turns around the line. 3. Pass the end of the line through the first loop, above the eye, and then through the large loop. Draw the knot into shape. 4. Slide the coils down tight against the eye. |
This is a very graphic intensive website it may take awhile for these pages to load up if you have a dial-up, please be patient! |
The Jansik Special Another beautifully simple knot that can be tied in the dark, The Jansik Special is a high strength knot. 1. Put 6 inches of line through the eye of the hook. 2. Bring it around in a circle and put the end through again. 3. Making a second circle, pass then end through a third time. 4. Holding the three circles of line against each other, wrap the end three times around the circles. 5. Either hold the hook steady with pliers, or make it fast to boat's rigging or safety lines. 6. Holding strain on the hook, pull on both ends of the line to tighten. |
The Palomar Knot The Palomar Knot is another very simple knot for terminal tackle. It is regarded by the International Game Fish Association consistently as the strongest knot known. It's great virtue is that it can safely be tied at night with a minimum of practice. 1. Double about 5 inches of line, and pass through the eye. 2. Tie a simple Overhand Knot in the doubled line, letting the hook hang loose. Avoid twisting the lines. 3. Pull the end of loop down, passing it completely over the hook. 4. Pull both ends of the line to draw up the knot. |
The Hangman's Knot There are at least 6 variations of the Hangman's Knot, - all of them excellent for terminal tackle, swivels and hooks. The "standard" Hangman's Knot holds only five turns when tied in monofilament nylon. If tied in rope, and used for its stated purpose, it takes eight turns. 1. Pass a 6 inch loop of line through the eye. 2. Bring the end back on itself, passing it under the doubled part. 3. Make five loops over the doubled part. 4. The formed knot is worked into shape. 5. The knot is sent down the line, against the eye of the hook or swivel. |
The Scaffold Knot This is a good strong knot that is fairly simple to tie. This knot is used by some flathead fishermen. 1. Pass a 6 inch loop of line through the eye. 2. Lock the upper part between thumb and forefinger, making a loop. 3. Make two more loops over the double part, holding them too, between thumb and forefinger. 4. Pass the end through the two loops just made, plus the first loop made in step2. 5. The formed knot can now be drawn into shape, and worked down against the eye of the hook or swivel. |
Turle Knot I have included the still-used Turle Knot for old times sake. Also known as the Turtle Knot, and Major Turle's Knot, it is simplicity itself to tie, but is one of the weakest knots. It should never be used for light lines, and there are better knots for use with heavy ones. 1. Pass the line through the eye of the hook. 2. Make a simple loop. 3. Carry the end of the line on to make a Simple Overhand Knot upon the loop. 4. Pass the loop over the hook. 5. Draw up into shape. |
Snelling A Hook Snelling a hook is a simple process once you know how it's done. 1. Pass the end of the line, trace or tippet through the eye twice, leaving a loop hanging below the hook. 2. Hold both lines along the shank of the hook. 3. Use the loop to wind tight coils around the shank and both lines, from the eye upwards. Use from 5 to 10 turns. 4. Use the fingers to hold these tight coils in place. Pull the line (extending from the eye) until the whole loop has passed under these tight coils. 5. With coils drawn up, use pliers to pull up the end of the line. |
The Blood Knot 1. Lie the ends of the two lines against each other, overlapping about 6 inches. 2. Take 5 turns around one line with the end of the other, and bring the end back where it's held between the two lines. 3. Repeat by taking 5 turns around the other line, bringing the end back between the two lines. These two ends should then project in opposite directions. 4. Work the knot up into loops, taking care that the two ends do not slip out of position. 5. Draw the knot up tightly. |
The Surgeon's End Loop If you need a loop, the Surgeon's End Loop is an easy way to go. It can be tied quickly and in the dark. 1. Take the end of the line and double it to form a loop of the required size. 2. Tie an Overhand Knot at the desired point, leaving the loop open. 3. Bring the doubled line through the loop again. 4. Hold the line and the end part together, and pull the loop to form a knot. |
The Blood Bight Knot Another end loop can be tied quickly and easily using the Blood Bight Knot. 1. Double the line back to make a loop of the size desired. 2. Bring the end of the loop twice over the doubled part. 3. Now pass the end of the loop through the first loop formed in the doubled part. 4. Draw the knot up into shape, keeping pressure on both lines. The Blood Bight Knot is often used for attaching a dropper when fishing deep water with several hooks. Some anglers attached the hook directly to the end of the loop, which should be at least 30cm from the end of the line. This is not a good practice, especially when the fish are shy. Far better to attach a single strand of nylon to a short Blood Bight Knot, using another Blood Bight Knot, or a Surgeon's Knot. |
The Dropper Loop A better method of forming a loop, or loops, in the line above the sinker is to use the old Dropper Loop. This draws into a knot that stands out at right angles to the line. If desired, the loops can be made long enough to have a hook set on them. And once again, this is not a good practice unless the fish are biting-mad, which they rarely are. 1. Form a loop in the line. 2. Take hold of one side of the loop, and make 6 or more turns around the line itself. 3. This is the tricky part - keep open the point where the turns, or twists, are being made. 4. Take hold of the other side of the loop, and pull it through the centre opening. Use a finger in this loop so that it is not lost. 5. Hold this loop between the teeth. Pull gently on both ends of the line, making the turns gather and pack down on either side of the loop. 6. Draw up the knot by pulling the lines as tightly as possible. The turns will make the loop stand at right angles to the line. |
The Float Stop The float fisherman uses a running float for casting and general handiness, and stops the float from running up the line by using the Float Stop. It has the advantage that the stops moves readily over the rod guides, but grips the monofilament nylon so tightly that it will not slide over the line. It should be made with about 5 inches of nylon, usually the same diameter as the line itself. 1. Take 2 turns (3 if necessary) around the main line at the chosen point. 2. Bring both ends around to form a Surgeon's Knot. 3. Tighten into shape bringing the coils close together. |